To put it simply a dead center is just that – dead. It has no moving parts. It is really nothing more than a metal shaft with a point. A live center is similar, but the shaft has a bearing that allows it to turn.
Subsequently, What is live Centre and dead Centre? a live center has internal bearings and the conical contact surface rotates with the workpiece. A dead center is just a stationary point, with rubbing contact between the cone and the workpiece.
Which part of lathe machine is called as live Centre? When turning between centres, a ‘dead centre’ is used in the headstock as well as the tailstock. As the one in the headstock revolves with the work, this centre is known as a live centre.
Considering this What is feed rod? Feed rod is a power transmission mechanism used for precise linear movement of the carriage along the longitudinal axis of the lathe.
Table of Contents
What is the difference between live Centre and dead Centre in lathe?
A center holds the work during rotation at the tailstock end of the lathe. A live center is mounted in bearings and rotates with the work, while a dead center does not rotate – the work rotates about it.
Secondly Which lathe machine is called dead center Mcq? Tail stock
Generally, it is situated on the right side of the Lathe machine. It supports the one end of the workpiece when it is too long. As it does not carry any moving parts, it is called the dead center.
What Operation Cannot be performed on lathe machine? Boring is the operation of enlarging the hole which is already drilled, punched or forged. It cannot produce a hole. Boring is similar to the external turning operation and can be performed in a lathe.
What is the function of dead Centre? A dead center (one that does not turn freely, i.e., dead) may be used to support the workpiece at either the fixed or rotating end of the machine. When used in the fixed position, a dead center produces friction between the workpiece and center, due to the rotation of the workpiece.
Which of the following have a live Centre *?
Which of the following have a live centre? Explanation: Head stock has live centre and it is called live because spindle rotates here and is not at rest during machining.
Why is it called centre lathe? A lathe is a machine tool that carries out many machine shop tasks. … The lathe holds and rotates the work piece about the center line of these two parts. It can also machine a part between its headstock and tailstock centers. This is why we call it a center lathe.
Which Centre is used for general work?
The included angle of centre is 60° for general purpose work and 75° for heavy work.
What is cross slide in lathe? Definition of cross slide
: a member of a machine (as of a lathe) on which the tool carriage moves at right angles to its principal direction of travel.
What is apron lathe?
Apron. The apron is a part of a lathe that’s clamped to the saddle. It’s designed to hold the gears, levers and other components that push the cross slide. Along with the saddle, the apron is a key component of the carriage, which as mentioned above, is used to guide the lathe’s tool bit.
What is cutting speed in lathe?
Cutting speed is defined as the speed at which the work moves with respect to the tool (usually measured in feet per minute). … Cutting speed and feed determines the surface finish, power requirements, and material removal rate.
What is Centre drilling on a lathe? A Centre Drill can also be used to provide a start location for a drill when drilling down the centre of a bar held in a Lathe chuck. Centre Drills are short and rigid enough to mark the bar centre without wandering off if they are carefully offered up to a rotating work-piece.
Why is it called center lathe? A lathe is a machine tool that carries out many machine shop tasks. … The lathe holds and rotates the work piece about the center line of these two parts. It can also machine a part between its headstock and tailstock centers. This is why we call it a center lathe.
What is the included angle of the life Centre nose?
In construction, both centres are identical, made as one unit that consists of a conical point of 60° included angle, a body provided with a Morse taper shank and a tang.
How many centers are in a lathe machine? Explanation: Most commonly two types of centres are there in lathe : live and dead centres. 2. Which of the following is not the type of centre in lathe? Explanation: Only live centre and dead centre are there in lathe.
What are the 12 lathe operation?
The most common lathe operations are turning, facing, grooving, parting, threading, drilling, boring, knurling, and tapping.
What is Contour turning? Abstract: Contour turning is a specific process of the machining on CNC lathes. In the finishing operation, to create the part profile, the turning tool must be moved in a trajectory of a complex flat curve (a toolpath) based on the part profile .
What is taper turning?
Taper turning is a machinings operation, which means that the diameter of cylindrical workpieces gradually decreases from one part to another. The taper can be external or internal. If the workpiece is taped outward, it has an outer taper. If it is taped inward, it has an internal taper.
What is Centre lathe machine? The Centre Lathe is used to manufacture cylindrical shapes from a range of materials including; steels and plastics. … This type of lathe is controlled by a person turning the various handles on the top slide and cross slide in order to make a product / part.
